fire retardant fabric logo

2653 Warfield Street Fort Worth, TX 76106

Flame Safe FIRE RETARDANT Coatings / Flame Retardants

Hotline: 800-333-9197 8am-5pm (CST) Ph: 817-740-9197

After Hours: 817-658-9197 email: fireprod@aol.com

 
Dallas, Fort Worth, Houston, Austin,South Dallas, North Dallas, Dallas County, Houston, Corpus Christi, San Antonio, Dallas - Fort Worth, Abilene, Amarillo, Odessa, Midland, El Paso
Fire Poly FP75I MSDS
Fire Retardant Coatings - Flame Retardant Coatings - Fire Retardant Sprays

FIRE POLY 75 I

INTERIOR FIRE RETARDANT
COATING or SPRAY
FOR ALL INTERIOR WOOD
PLYWOOD ● LUMBER ● TIMBER


  CLASSIFIED
FIRE RETARDANT COATING
SURFACE BURNING CHARACTERISTICS OF APPLIED COATING

Surface
Wood
Flame spread
<25
Smoke developed
<100
Number of preliminary coats
None
Rate per coat (ft2/gal)
--
Number of fire retardant coats
3
Rate per coat (ft2/gal)
500
Number of overcoats
None
Rate per coat (ft2/gal)
--
Flash point of liquid coating:  
  Fire retarding coating - closed cup, no flash


fire retardant logo

FIRE POLY FP75I

TECHNICAL DATA

INTERIOR CLASS A FIRE RETARANT COATING RATING

PRODUCT DESCRIPTION:    Aqueous Based Resin

PRODUCT ANALYSIS
Total Solids
46%   PH
2.5 - 2.8
Weight per gallon
10.7 lbs Flash point
Non-Flammable
Specific gravity
1.33 Color
Water clear at 78°F. - Slight haze at 50°F. or lower
Volatability
Non-Volatile Solvents
Water(Contains no petroleum or derivatives of petroleum)
Anti-Fungus
excellent Resistance Bacterial
Good Resistance
Linear shrinkage
None Moisture Absorption
None
Corrosive
Mildly Toxic
None (when dry)
Insects, rodents,
aspergilli And other types of molds
Excellent resistance Termites
Excellent resistance
Preservative for wood
None Scrubability
1000 cycles

RECOMMENDED USE: Interior Class A Rating (Flame spread less than 25)

FLAME SAFE FIRE POLY 75I is a fire retardant coating. It can be used on:

Yellow Pine Redwood Cedar
Douglas Fir Plywood OSB
Mahoghany Cypress MDF
Wall Coverings Particle Board Corrugated Board

ENVIRONMENTAL REGULATION:

This product complies will U. S. Federal Regulations concerning the use of lead in paint and hydrocarbon emissions.


QUICK REFERENCE FOR APPLYING FIRE POLY FP 75I FIRE RETARDANT COATING

MATERIAL
APPLICATION
COVERAGE

Interior wood
Any type

Treat before, during or after construction.

Be sure surface is clean and dry before treating.

Apply with sprayer head held at 8 to 12 inches from surface

Apply with brush or roller.

May be necessary to wipe on hardwood surfaces

Treat all surface areas where possible

Do not expose treated area to moisture for 24 hours.

Apply three (3) coats at 500 sq. ft. per gallon with the final coverage rate of 166.3 sq. ft. per gallon

INTERIOR WOODS

           All surfaces to be treated must be clean and dry. Fire Poly 75I fire retardant coating is water-based, clear liquid that becomes insoluble when dry. Fire Poly 75I fire retardant coatintg also acts mold and mildew protector and repels insects. If over coating is intended, Fire Poly 75I is an excellent surface primer for use under latex paints or can be use as a finished coat overwater based stains.

DO NOT DILUTE OR MIX FIRE POLY 100 WITH ANY OTHER PRODUCTS.

   Avoid wasteful runs and dripping.  It should be noted that unlike some products, materials treated with Fire Poly 75I fire retarant coating require no special cutting tools or special fasteners. Contact parts of any equipment should be stainless steel or plastic to prevent chemical reaction and breakdown. Storage may be done in polyethylene containers.

     Structures under construction can be made fire resistant. As soon as the surface is enclosed, spray all exposed interior surfaces (studs, trusses, subfloor, joists, interior of outside walls, etc. with Fire Poly FP 75I fire retardant coating, Use on substrates that are enclosed and/or in areas that are warm and dry. This will provide the structure with a long term fire retardant protection.

 

wood ceiling

Interior with wood pitch ceiling

 

CAUTION:

          Product must not freeze. It must not be thinned or diluted.

OVERSPRAY:

        The overspray will not harm plants or animals. Spills can be flushed with water. A rag wetted with   bleach and water mix will clean up spotting.

CLEAN UP PROCEDURE:

          Airless Equipment.

1. Run clear water through the system until coating is flushed out. When minor sudsing on surface stops, the system is flushed.

2. Run bleach and water mix (1 part to 4 parts) through system as solvent for cleaning any residue.

            3. Repeat Step 1 if any foaming occurs in Step 2.

            4. Lubricate system as specified by equipment manufacturer to combat rusting.

If two or more applications are planned in the same day, the sprayer can be kept clean by running water through the system between applications.

          Brushes/Rollers.

              1. Clean immediately after use.

              2. Wash thoroughly with bleach and water mix (1 part to 4 parts).

SAFETY FIRST

Use approved safety devices (ropes, belts, ridge hooks, ladder, etc.) When working on steep or high areas. Take EXTREME CARE not to step on wet treated area. Surface may be slick until dry.

It is good practice to wear respirator or mask and protect hands with rubber gloves when spraying any coating or chemical. When engineered air control is not feasible, use properly maintained and properly fitted NIOSH approved respirator for solvent vapors. A dusk mask does not provide protection against vapors.

If eye contact occurs, flood with water for fifteen (15) minutes and call a physician. KEEP OUT OF REACH OF CHILDREN. DO NOT TAKE INTERNALLY.

interior wood finish

Interior Wood Finishes

interior wood framing

Call for pricing and ordering 1-800-333-9197

HOME | CONTACTS | PRODUCTS |Fire Poly FP75I MSDS | TESTING